Just How to Install a Bathtub Yourself: Removing as well as Replacing.
Just How to Install a Bathtub Yourself: Removing as well as Replacing.
Blog Article
Were you searching for additional info concerning Installing A Bathtub?
Setting up a tub isn't specifically brain surgery, but it does require solid plumbing, carpentry, as well as often, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably tough job. If the old bathtub is conveniently obtainable, the task can relocate easily; if you need to open up a wall surface to remove the old tub and also place the brand-new bathtub, the task is much harder. In either situation, the task is within a residence handyman's abilities, although you will need a helper to move out the old tub and embeded in the brand-new one. See to it you have actually certified on your own for the work and also fit trying it. Instead of employing a professional to take over a halfway-completed project, it is better to consider using one prior to you start. Possibilities are you may need a professional plumber to make tube links.
This write-up will help you install a new bath tub in your restroom if you have currently acquired a new bathtub and don't require to alter the plan of your previous supply of water pipes.
Your devices and also product checklist should consist of the following:
Getting ready for the Installation
To start with, the supporting frame provided with the bath should be fitted (if called for) according to the maker's instructions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to ensure that if the tap features a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the taps device to avoid strain on the bathtub.
Fit the adaptable tap connectors to the bottom of both taps making use of 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize all of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its last position.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your setup, after that the first thing you ought to do is separate the water supply. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome because of the limited gain access to that is usually the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will certainly come from the pipes. When the supply pipelines have been eliminated, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from transforming throughout this process. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any type of old securing substance.
Before carrying on to fit the brand-new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, position the bathtub in the needed placement. The wood boards are handy in evenly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four little points.
The next objective is to make sure that the tub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the bathtub until the spirit level checks out degree.
To set up faucets, fit all-time low of the outermost flexible tap connector to the suitable supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water and also check all joints and new pipework for leaks and tighten them if required. Fill up the tub and likewise inspect the overflow electrical outlet as well as the typical electrical outlet for leakages.
Lastly, fix the bath paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bathtub should wait till the bath tub has actually been utilized at least once as this will certainly resolve it into its final placement.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will certainly need a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a link to the existing supply pipes.
If you need to fit a monobloc, after that you will require lowering couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the faucet in the placing opening in the bath/basin guaranteeing that the washers remain in location between the tap and also the sink. Protect the tap in place with the supplier supplied backnut. When the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular faucet connectors. The previous kind ought to be connected to the faucet ends first, tightening only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to break a rigid seal, creating the water to permeate the wall surface in between the bathroom and also the tiling, resulting in complications with wetness and feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and can sealing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly load the tub with water prior to securing, to allow for the motion experienced when the bathtub is in use. The sealer can fracture fairly very early if you do not take into account this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also quickly readily available on the market. It is recommended to fit the ceramic tiles making use of water-resistant or waterproof sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an avid reader on A Step-by-Step Guide to Installing a Bathtub, I figured sharing that piece of content was worth the trouble. Be sure to take the opportunity to distribute this blog entry if you enjoyed reading it. We appreciate reading our article about How to Install a Bathtub.
Visit Homepage Report this page